Panasonic kx t308 manual

The wall where the main unit is to be mounted must be able to support the weight of the main unit. If screws other than the ones supplied are used, use screws with the same diameter as the ones enclosed. Connect the frame of the main unit to the ground.

Loosen the screw. Insert the grounding wire user- supplied. To the ground 3. Tighten the screw. Screw 4. Connect the grounding wire to the ground. Page 23 2. Near the protector 2 Check obstructions. Telephone Wiring The maximum length of the extension line cord twisted cable which connects the system and the extension is as follows.

Page Paralleled Telephone Connection Any single line telephone can be connected in parallel with a proprietary telephone as follows. Page Polarity Sensitive Telephone Connection 2.

Complete all the required extension wiring. Confirm that dialing can be done from all the extensions using a touch-tone telephone. If dialing fails, the polarity between the extension and the system must be reversed. Page Printer And Pc Connection 2.

These are used to print out or refer to the SMDR call records and system programming data. Page 31 2. Page 32 2. Remove the 2 screws. Maximum cable length The maximum length of the doorphone and door opener line cord which connects the system is as follows. Diameter of the line Max.

Page 37 Doorphone 1 Doorphone 3 4-conductor wiring is required. Page Backup Batteries Connection 2. Loosen the screws and open the top and bottom front covers. Page 41 2. After cutting the areas, be sure to cut off any excess plastic in order to make the surface smooth. First, insert the plastic spacer into the hole on the KX-TA Attach the 2 extension connectors to the system, install the KX-TA and secure the 2 extension bolts.

Page 42 1. Loosen the screws and open the front and bottom front covers. Page 43 JACK 17 through Wrap the strap around all of the cords. Close the covers and secure the screws. Insert the rivet into the hole in the strap. Insert the rivet and strap into the hole on the system. Page Closing The Front Cover 1. Replace the covers and tighten the screws. Tie together all of the connected cords and attach them to the wall so that the cords cannot be pulled out of the system.

Plug the AC power cord into the system and an AC outlet. Turn the Power Switch on. The power indicator will light. Page 48 2. Assemble as shown below, using the plug which fits your socket. In this case, be sure to connect the frame of the main unit to ground because the ground line in the power cable cannot be used. Page System Restart 2. Before restarting the system, try the system feature again to confirm whether there definitely is a problem or not.

System Restart causes the following. Otherwise, the system will not clear. Page 51 Section 3 Features One of 6 messages can be programmed as desired, which are available for any telephone single line telephone or proprietary telephone. When an extension user dials an Automatic Line Access number before a telephone number, an available outside CO line from the assigned lines in program [] is seized automatically. Each time a digit is dialed, the system checks the Is the dialed number a toll Reorder tone dialed number other than Host PBX access codes, restriction denied code?

Carrier excepted codes and 1st carrier access code. Page Call Forwarding Features Call Forwarding Allows an extension user to transfer incoming calls automatically to another extension or to an external destination. The following types are available. All Calls: All incoming calls are forwarded to another extension. Busy or No Answer: All incoming calls are forwarded to another extension when the extension user does not answer within the programmed time in [] or when the extension is busy.

The CPC signal detection is activated by programs [] and []. Program [] is for incoming outside calls, and [] is for outgoing outside calls. Page Call Transfer — To Extension Features Call Transfer — to Extension Allows an extension user to transfer a received call, an intercom or an outside call, to another extension.

Two types are available. Screened Call Transfer: Announces the call to another extension before completing the transfer. Unscreened Call Transfer:Immediately releases the call to another extension without an announcement. The maximum number of members of a conference can be programmed in program []. When the specified time expires, both lines are disconnected.

A warning tone is sent to both parties 15 seconds before the time-limit. Enter the extension number. Enter the DISA phone number. The caller reaches the DISA line. This is the time between a call reaching the system and being received. The time is assigned in program []. The system regards the call as unanswered. The extension will not receive intercom or outside calls. A 3-party conference will be established.

In an extension group, the following features can be activated. This is done by placing the current call on hold and sending a flash signal using either the FLASH button or the feature number.

This feature is effective only during an outside call. Switch the selection mode before using the headset optional. The held call can be retrieved by the user who held it, or by any other extension Call Hold Retrieve. With a single line telephone SLT , either one outside or intercom call can be held at one time.

Page Hookswitch Flash Features Hookswitch Flash Flashing the hookswitch is used to allow a single line telephone user to hold a call for transferring or holding, if the flash time is within the assigned time in program []. Flashing the hookswitch can be also used to disconnect a call, if the flash time is more than the assigned time in program []. The Intercept Routing feature works in the following 2 cases. The selected language in program [] is used for an SMDR printout. This allows making or receiving outside calls.

Embed Size px x x x x Attention If there is any trouble, disconnect the unit from the telephone line. Plug the telephone directly. If the telephone operates properly, do not reconnect the unit to the lineuntil the problem has been repaired by an authorized Panasonic Factory Service Center.

If thetelephone does not operate properly, chances are that the problem is in the telephone system,and not in the unit. Keep the unit away from heating appliances and electrical noise generating devices such asfluorescent lamps, motors and televisions. These noise sources can interfere with theperformance of the unit. This unit should be kept free of dust, moisture, high temperature more than 40 C [ F] and vibration, and should not be exposed to direct sunlight.

Never attempt to insert wires, pins, etc. Do not use benzene, thinner, or the like, or any abrasive powder to clean the cabinet. Wipe it. When you ship the productCarefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a postage-paid letter, detailing the symptom, to the outside of the carton. They are NOT equipped to make repairs.

Product servicePanasonic Factory Servicenters for this product are listed in the servicenter directory. Consult acertified Panasonic dealer for detailed instructions. Accessory Order Information Replacement parts and accessories are available through your local authorized parts distributor. For ordering accessories, call toll free It is to be used after the system is installed and System Programming iscompleted.

The step-by-step procedures required to activate each feature are explained in detail. It also provides an illustration of eachtelephone, identifies their feature buttons, supplies background information on thesefeature buttons, and gives the initial settings.

Features and CapabilitiesKX-TA is a sophisticated and powerful system which fulfills your expectations of anoffice communications system. The following types are available. Off: Both features are not set. System programming is required to execute this feature. The canceling depends on the Call Forwarding type that has been assigned. Only the user who held the call can retrieve it. Press HOLD again.

If the call is not answered, the call information is automatically recorded. There are two kinds of call log areas available in the system. One is the personal area, which stores call logs for each extension. When the Caller ID Indication — Common button indicator is red, there are new calls logged in the common area. Page Call Park Telephone Features Call Park Allows you to place a held call into a system parking area so that you can perform other tasks.

The parked call can be retrieved by any extension user. Up to ten calls can be parked. Page Call Pickup, Group Call Pickup, Group Allows you to answer a call that is ringing at another telephone within your extension group. System Programming is required to use this feature. If a call is received while you are already on the line, you can place the current call on hold and have a conversation with the other party.

There are two ways. Screened Call Transfer: The destination confirms the transfer before sending. You can answer the second call by disconnecting the first call or placing it on hold. You can respond to the call by placing the first call on hold.

In this situation, the caller information is automatically recorded in your personal area and your Caller ID Indication — Page Conference Conference During a two-party conversation, you can add a third party to make a three-party conference. The members of a conference may be three extensions, one extension and two outside CO lines, or two extensions and one outside CO line. To talk to the original party while holding the third party Flash the hookswitch.

The tone can be disabled. Page Conference, Unattended Telephone Features Conference, Unattended When you are in a conference with two outside parties, you can leave the conference call allowing the other two parties to continue their conversation.

Data communication devices, such as computers and facsimiles, can operate uninterrupted. A pre-assigned DISA security code may be necessary, depending on the mode, to access the features directly. Your extension will not receive intercom or outside calls.

Up to two door openers can be connected to the system. Page Doorphone Call Doorphone Call Allows you to have a conversation with a visitor at your doorphone.

Up to two doorphones can be connected to the system. Calling an extension from a doorphone Any Doorphone Press the Doorphone button for one second. Answering a doorphone call Any Telephone When you hear the doorphone ring tone at the extension Calling a doorphone Page Electronic Station Lockout Electronic Station Lockout Allows you to lock your extension so that other users cannot make outside calls from your extension.

Locking Any Telephone Dial However, calls can be made at a locked extension depending on system programming. Any Telephone If you make an intercom call and while hearing a busy tone Dial 2. This feature is effective only during an outside call. Page Flash Telephone Features Flash Allows you to disconnect the current call and make another call without hanging up. Using the handset Any Telephone Lift the handset.

After subscription, the voice mail system can answer calls automatically when you are busy or calls are not answered, and callers can leave their messages in your mailbox of the voice mail system located at the telephone company. Page Lockout Lockout If one party in a conversation goes on-hook, both parties will be disconnected from the speech path automatically. A reorder tone is sent to the off-hook party before it is disconnected.

No operation is necessary. When in the Log-Out mode, you can leave the group temporarily, preventing hunting calls from being sent to your extension. In other words, the last member of the group cannot log out. The Another Extension Message Waiting button light on your extension lets you know that another extension has a message waiting. You can call back the message sender by a simple operation.

Unlocking Any Telephone Dial You will still be able to hear the other party. This is done by storing an extension number, telephone number or feature number up to twenty-four digits in a One-Touch Dialing button. One extension can be assigned as an operator. The paged person can answer your page from a nearby telephone.

You cannot be paged at a single line telephone, but you can answer a page, which is announced over nearby PTs or an external pager, from your single line telephone.

Your message is announced over the built-in speakers of proprietary telephones PT and the external pager. Page Paging - Group Paging — Group Allows you to select an extension group and make a voice announcement. You can select all extension groups simultaneously. For an SLT: Flash the hookswitch.

Wait for an answer. Dial Page Paralleled Telephone Connection Paralleled Telephone Connection Any extension can be connected in parallel with a proprietary telephone and a single line telephone. In the event of a power failure, CO1 can be accessed using the single line telephone that is connected in parallel with the proprietary telephone to jack number If the extension receives a call, ringing will be heard from the proprietary telephone and the single line telephone.

These numbers are available for your extension only.